MIBO 1/10 Onroad Low Profile (0.074s/14kg/8.4V) Coreless Servo MB-2312
Specifications:
Servo dimensions Low Profile
Servo type Digital
Programmable Yes
Thrust at 4.8V [kg/cm] 10
Thrust at 6.0V [kg/cm] 12
Thrust at 7.4V [kg/cm] 13
Thrust at 8.4V [kg/cm] 14
Speed at 4.8V [s/60st.] 0.105
Speed at 6.0V [s/60st.] 0.093
Speed at 7.4V [s/60st.] 0.0828
Speed at 8.4V [s/60st.] 0.074
Servo gears Metal
Ball bearings 2×
High-voltage Yes
Power supply [V] 4.8 - 8.4
Length [mm] 40
Width [mm] 20.2
Height [mm] 26.1
Weight [g] 48
Intended for On-road cars
Cable length [mm] 50
-
Secure Payment Guarantee. Personal information encrypted and protected under the GDPR.
-
We deliver in Portugal, Europe and Brazil.
-
Returns up to 14 days after receipt of your order.
Description
High torque/very high speed digital low-profile servo with steel gear and double BB-ed output shaft. Works great in 1:10 on-road RC cars (suitable for Modified, Stock, FWD, Formula classes). An aluminium middle part of the servo case for perfect cooling under high load.
MB-2312 is programmable using the KAVAN servo USB programmer/interface and PC software.
Programmable Functions:
Servo Angle: Maximal servo rotation angle range setting. The default range is ca. 120° within the regular RC signal pulse width range (900~2100µs); ca. 180° within the max. signal pulse width range (500~2500 µs).
Servo Neutral: Servo neutral (centre) position setting.
Damping Factor: Servo damping setting – adjust the characteristics of the servo when stopping.
PWM Power: Adjusts the servo output power. The higher the power, the higher the speed and torque of the servo – indeed also the current consumption will be higher.
Sensitivity: Servo sensitivity (Dead Band) setting. The higher sensitivity the narrower the dead band – servo moves only if the change of the signal pulse width is bigger than the dead bandwidth. Too high setting may cause servo jitter in some applications. Range: Ultra High (ca. 1 µs dead band) – High (ca. 2 µs) – Medium (ca. 3 µs) – Low (ca. 4 µs)
Soft Start: Turns on/off the soft start feature. If ON, the servo goes slowly to the initial position corresponding to the servo signal once the power is switched on.
Reverse: Reverses the servo movement direction.
Narrow Band: FUTABA SR Mode – only for use with FUTABA radio channels working in the SR mode. Do not turn the option on if you are using a different setting of your FUTABA radio or any other radio.
SANWA SSR: SANWA SSR Mode - only for use with SANWA radio channels working in the SSR mode. Do not turn the option on if you are using a different setting of your SANWA radio or any other radio.
Lost PPM Protection (Fail-Safe): In the case the control signal from the receiver is lost completely or cannot be decoded correctly (due to interference) the servo can use choose one of three fail-safe modes:
(a) Release: No fail-safe protection.
(b) Keep Position: Keeps the position corresponding to the last correct control signal.
(c) Go Neutral Position: The servo returns to the neutral (1500µs pulse width) position.
Over Load protection: Enables or disables overload protection of the servo in three levels – once the overload conditions last for the pre-set time (in seconds), the output power of the servo is reduced to the corresponding pre-set level (% of the max. power).
Default: Restores the factory default setting of the connected servo.
Wide input voltage range 4.8–7.4 V (nominal); operating voltage range 4.8–8.4 V.
25T/5.92mm output shaft.
Specifications:
Servo dimensions Low Profile
Servo type Digital
Programmable Yes
Thrust at 4.8V [kg/cm] 10
Thrust at 6.0V [kg/cm] 12
Thrust at 7.4V [kg/cm] 13
Thrust at 8.4V [kg/cm] 14
Speed at 4.8V [s/60st.] 0.105
Speed at 6.0V [s/60st.] 0.093
Speed at 7.4V [s/60st.] 0.0828
Speed at 8.4V [s/60st.] 0.074
Servo gears Metal
Ball bearings 2×
High-voltage Yes
Power supply [V] 4.8 - 8.4
Length [mm] 40
Width [mm] 20.2
Height [mm] 26.1
Weight [g] 48
Intended for On-road cars
Cable length [mm] 50