C0271 Mugen Seiki 3x13.8mm Joint Pin
€3.98
These are replacement 3x13.8mm joint pins for Mugen buggies and fits the MBX5 family of buggies.
MBX8ECOTE
Spares for Mugen MBX8ECOTE Nitro 1/8 Off Road.
C0264 Mugen Seiki Universal Joint Shaft
€3.74
C0264 Mugen Seiki Universal Joint ShaftThis is a set of replacement joint shafts for the universals used in the Mugen MBX5 buggie
E0135-B Mugen Seiki Suspension Arm Spacer Set
€6.54
This is a replacement Mugen Suspension Arm Spacer Set, and is intended for use with the Mugen MBX7 1/8 scale nitro buggy.
E0546 Mugen Seiki Damper Cap Bushing (4)
€5.04
This is a set of four replacement Mugen Damper Cap Bushings, and are intended for use with the Mugen MBX6 family of 1/8 Scale vehicles.
E2108 Mugen Seiki Complete Bushing Set
€11.30
This is a replacement Mugen Complete Bushing Set, and is intended for use with the Mugen MBX7 1/8 scale nitro buggy. This complete set includes all of bushings used in the suspension mounts to adjust toe angle, kick-up and anti-squat on the vehicle.
C0270 Mugen Seiki 3x12.8mm Joint Pin
€3.65
This is a set of replacement joint pins for the universals used in the Mugen MBX5 buggies, and are used to hold the universal joint together and go through the axle shafts and the joint shaft.
E2149 Mugen MBX8 Aluminum Front/Front Lower Arm Mount
€19.92
This is a replacement Mugen MBX8 Aluminum Lower Arm Mount, for use on the front gearbox, in the front location.
E2237 Mugen Seiki HTD Differential Cup Outdrive (2)
€15.57
This is a pack of two replacement Mugen HTD Differential Cup Outdrives for use with the optional HTD (High Traction Diff) Differentials.
copy of E2422 Mugen Seiki MBX8 1-Piece Wing Stay
€13.90
This is the Mugen MBX8 1-Piece Wing Stay Set, including the wing stay, wing stay brace and four plastic wing buttons.
E2168 Mugen Seiki Carbon Front Upright Arm (-3mm) (2)
€18.29
The Mugen Carbon Front Upright Arms offer improved initial steering response, and makes the vehicle more stable through the middle and exit of the corner. They also help to reduce bump steer and make the vehicle more predictable in bumpy conditions.
C0265 Mugen Seiki 2.5x15.8mm Universal Joint Pin
€2.65
This is a set of replacement joint pins for the universals used in the Mugen MBX5 buggies, and are used to hold the universal joint together and go through the axle shafts and the joint shaft.
E2241 Mugen Seiki HTD Differential Gasket (10)
€9.51
This is a pack of ten replacement Mugen HTD Differential Gaskets for use with the optional HTD (High Traction Diff) Differentials.
E2132 Mugen Front Upper Suspension Arm Set
€11.14
These front upper suspension arms have been shortened 1.6mm in length. This will allow the use of the MUGE0161 spacer between the pillar ball and the upper arm. This will allow for the same camber on each side of the buggy.
E2564 Mugen Seiki MBX8 Shock Retaining Pin (4)
€10.28
This is a pack of four optional Mugen Seiki Big Bore Blank Shock Pistons. Create your own custom piston hole sizes with these blank pistons.
E0545 Mugen Seiki Damper End Set
€8.13
This is a replacement Mugen Damper End Set, and is intended for use with the Mugen MBX family of 1/8 Scale vehicles. This set includes four shaft ends and four spring cups.
E0174 Mugen Seiki Washer Set
€9.27
This is a set of replacement Mugen washers, and are intended for use with the Mugen MBX series 1/8 scale vehicles.
E2232 Mugen Seiki HTD Differential Case
€10.49
This is a replacement Mugen Differential Case for use with the optional HTD (High Traction Diff) Differentials.
E2116 Mugen Seiki Rear Hub Carrier Hinge Pin (2)
€13.74
This is a pack of two replacement Mugen Rear Hub Carrier Hinge Pins, and are intended for use with the Mugen MBX 1/8 scale nitro buggy. These hinge pins secure the rear hub carrier to the rear arm.
E0811-B Mugen Seiki Rear Upper Arm Link (Long)
€4.80
This is a the new optional long rear upper arm link that comes with the Mugen MBX buggy kits.
E2242 Mugen Seiki HTD S6 Silicon O-Ring (10)
€5.41
This is a pack of ten replacement Mugen HTD S6 Silicon O-Rings for use with the HTD (High Traction Diff) Differentials
E0705 Mugen Seiki Flywheel Washer/Spacers (4)
€3.09
This is a set of four replacement Mugen Seiki Flywheel Washer/Spacers, and are intended for use with the Mugen MBX6 family of 1/8 scale vehicles.
E0717A Mugen Seiki 0.95mm Clutch Spring Set (3)
€7.40
This is a set of optional Mugen 0.95mm Clutch Springs. The stiffer the spring, the later the clutch will engage allowing the engine to spool up to a higher RPM range before the clutch comes on.
E2156 Mugen 1mm MBX8 Graphite Rear Lower Arm Plate (2)
€19.19
This is a pack of two optional Mugen 1mm MBX8 Graphite Rear Lower Arm Plates. These plates attach to the suspension arm to increase stiffness. Mounting hardware not included.
E2138 Mugen Seiki 2.5mm Rear Anti-Roll Bar
€10.16
This is an optional Mugen 2.5mm Rear Anti-Roll Bar.
E2142 Mugen Seiki MBX8 Gearbox
€13.90
This is a replacement Mugen MBX8 Gear Box. This gearbox has been updated to allow you to remove and service the differential without detaching the suspension arm mounts.
E2260 Mugen Seiki MBX8 Center Joint Cup
€10.49
This is an optional Mugen MBX8 Center Joint Cup.
E0161 Mugen Seiki Front Track Width Adjustment Spacer (4)
€5.20
This is a set of replacement Mugen front track width adjustment spacers, and are intended for use with the Mugen MBX6 and MBX6T 1/8 scale vehicles.
FP2151 FP Aluminum One Piece Wing Button: MBX, Associated, Xray
€12.19
FP2151 FP Aluminum One Piece Wing Button: MBX, Associated, Xray.
E0517 Mugen Seiki Front Shock Shaft (2)
€9.51
This is a pack of two replacement front shock shafts for the Mugen MBX7 and MBX5T truggy.
E0710 Mugen Seiki Aluminum Clutch Shoes (3) (Hard)
€30.57
E0710 Mugen Seiki Aluminum Clutch Shoes (3) (Hard)
E2516 Mugen Front Damper Spring 1.6 L70/9.25T: X8, X8T
€13.00
Mugen Seiki 70mm Front Shock Spring Set (Soft - 1.6/9.25T) (2).
C0601/1 Mugen Seiki 8x16x5mm Bearing (10)
€20.32
C0601/1 Mugen Seiki 8x16x5mm Bearing (10)
E0167 Mugen Seiki 2.6mm Front Anti-Roll Bar
€9.19
This is a Mugen 2.6mm front anti-roll bar, and is intended for use with the Mugen MBX6 and MBX6T 1/8 scale vehicles.
E2124 Mugen Seiki Steel Kingpin Ball Adjusting Nut (2)
€9.84
This is a pack of two optional Mugen Steel Kingpin Ball Adjusting Nuts. These nuts are heavier than the stock parts, and eliminate the need for arm weights.
E0813 Mugen Seiki Rear Upper Arm Link
€6.54
This is the replacement rear upper arm link assembly ends for the Mugen MBX.
E2252 Mugen Seiki MBX8 Straight Cut Bevel Gear (12T)
€13.90
This is an optional Mugen 12 Tooth MBX8 Straight Cut Bevel Gear.
E2422 Mugen Seiki MBX8 1-Piece Wing Stay
€11.99
This is the Mugen MBX8 1-Piece Wing Stay Set, including the wing stay, wing stay brace and four plastic wing buttons.
E2137 Mugen Seiki 2.8mm Front Anti-Roll Bar
€10.16
This is an optional Mugen 2.8mm Front Anti-Roll Bar. This bar is slightly thicker than the standard 2.7mm bar included with the MGT7 and MGT7E.
E2409 Mugen Seiki Stone Guard for MBX7/MBX8
€13.66
This is a plastic set of side / stone guards. X8/E, X7R/E, X7TR/E, GT7
E2172 Mugen MBX8 Rear Hubs Set
€10.12
This is a replacement Mugen MBX8 Rear hubs Set. No mounting hardware.
E2432 MUGEN CHASSIS X8R NITRO
€81.71
E2432 MUGEN CHASSIS X8R NITRO
E2161 Mugen Front Lower Suspension Arm L/R: X8T, X8TE
€17.48
This is a replacement Mugen Front Lower Suspension Arm Set for use with the MBX8T and MBX8TE truggies. This set includes direction left and right side arms, with plastic arm inserts.
E2219 Mugen Seiki Rear Universal Set
€50.81
This is a replacement Mugen Rear Universal Set. These redesigned universal drive shafts are must be used with the MUGE2131 uprights and require a 8x16x5mm ball bearing. The length of the drive shaft is 89.5mm.
Mugen MBX8 REAR LOWER ARM MOUNT F -E2175
€22.52
Mugen MBX8 REAR LOWER ARM MOUNT F -E2175
E0176 Mugen Seiki 2.6mm Rear Anti-Roll Bar
€9.27
This is a Mugen 2.6mm rear anti-roll bar, and is intended for use with the Mugen MBX6 and MBX6T 1/8 scale vehicles.
E2123 Mugen Seiki Steel Kingpin Balls (2)
€17.48
This is a pack of two optional Mugen Steel Kingpin Balls. These kingpin balls are heavier than the stock parts, and eliminate the need for arm weights.
E2147 Mugen 1.5mm Trailing Front Hub Carrier Set
€11.22
This is an optional Mugen Seiki 1.5mm Trailing Front Hub Carrier Set that can be used with CVA (MUGE0221 & MUGE0224) and universal driveshaft on all the MBX family of buggies, trucks, and GT vehicles. Package includes one left and right side, as well as four inserts.